Enclosures
|
| Additional
Rough in Boxes, Surface Mount Boxes and Enclosures for your SAC |
Rough
In Box 100
The RIB100 is the rough-in box that comes with every
Security Access Console.
This rough in box has holes on both sides for easy mounting in
any framing application.
This rough-in box is designed to be sunk into the wall to provide
a surface mount for you SAC.
Dimensions: (4” Wide x 7.5” Tall x 3” Deep) |
 |
|
|
|
Rough
In Box 200
The RIB200 is our rough-in box for block, brick
and poured concrete walls.
This rough-in box is designed to be sunk into the wall to provide
a surface mount for you SAC.
Dimensions: (4” Wide x 7.5” Tall x 5”
Deep) |
 |
|
|
|
Rough
In Box 300
The RIB300 is our rough-in box for block, brick and
poured concrete walls.
This specially designed rough-in box is perfect for outside walls. It has a built
in rain shield to keep the sun and rain off of your SAC.
This super tough sealed box is made with extra thick metal and is 6" deep
with room to spare for all of its electronics.
It has knockouts on both sides and the bottom measuring .5" and .75" for
easy hookup to conduit.
The RIB300 is also sealed with a black crinkle powder coat to give a lifetime
of service without rusting.
The RIB300 is sealed top to bottom to keep out moisture from your SAC.
Dimensions: (4.75” Wide x 8.25” Tall x 7” Bottom 8.25” Top
Deep) |
 |
 |
| Side
View |
 |
 |
| Bottom
View |
Back
View |
|
|
|
 |
| Color & Texture |
|
|
Surface
Mount Box 100
The SMB100 is our surface mount box for use when
a rough-in box is not an option.
The SMB100 screws directly to any surface and can be easily
sealed with calk.
This surface mount box is sealed to keep the moisture out
and has no ugly seam.
The box is only 1.5" deep and slightly smaller than
the SAC100 or SAC200 faceplates.
The box mounts easily and securely with enough room for the
camera, intercom and keypad.
It is also sealed with a black powder coat to give a lifetime
of service without rusting.
Dimensions: (4.375” Wide x 7.875” Tall x 1.5” Deep) |
 |
 |
| Back
& Side
View |
|
|
 |
| Color & Texture |
|
|
Standing
Pole Enclosures for your SAC (Gooseneck Poles) |
Standing
Pole Enclosure 100
The SPE100 is our standing pole enclosure that is used
to enclose the SAC100 or 200 at a gate or driveway application.
The enclosure has enough room to house all of our SAC models
including, camera, microphone, speaker, Essex illuminated
keypad and controller board.
The enclosure also has a rain cover for the SAC and is
sealed to keep moisture out.
The enclosure, pole and base plate are made of extra thick
metal and powder coated with a black crinkle powder coat
to last a lifetime and look great.
The enclosure has the capability to bolt the Essex circuit
board down using hinges. This gives you the ability to
swing the circuit board to the side and out of the way
if you need to run wires at a later time.
The pole can easily be routed with wires and comes with
a mounting base plate to bolt to a concrete slab or a curb
and base cover. The base cover will cover the bolts for
that clean look.
Dimensions: (The SPE100 is 47” tall and 23” deep.
From the faceplate to the front of the base plate is 15.5”.
The 4 mounting holes are .5” in diameter)
What’s included:
- (1)
SPE100
- (4)
Anchor Bolts
- (8)
Nuts
- (4)
Washers
- (2)
Hinged Standoffs
SAC
Not Included
|
 |
|
|
|
| Color & Texture |
|
|
Standing
Pole Enclosure 100 Mounting Plate
The SPE100MP is used with the SPE100. It is buried
in wet concrete at the time of construction as a template
for the base of the SPE100.
This item is a steel plate template and 4 j-bolts attached
with a hole punched out in the middle. It is designed
for you or the contractor to install it when the concrete
is being poured. Just bury it up to the steel plate and
level it with the conduit protruding up from the hole
on the middle.
Then when the construction is done and the concrete
is dry, bolt down the SPE100 and you’re done.
This keeps the SPE100 from being exposed to construction
damage.
Dimensions: 5.25” x 5.25”, hole in center
is 1.375” J-bolts 6” long
What’s included:
- (1)
Mounting Plate
- (4)
J Bolts
- (8)
Nuts
- (4)
Washers
|
 |
|
|
|
Standing
Pole Enclosure 200
The SPE200 is our standing pole enclosure that is used to
enclose the SAC100 or 200 at a gate or driveway application.
The enclosure has enough room to house all of our SAC models
including, camera, microphone, speaker, Essex illuminated keypad
and controller board.
The enclosure also has a rain cover for the SAC and is sealed
to keep moisture out.
The enclosure and pole are made of extra thick metal and powder
coated with a black crinkle powder coat to last a lifetime
and look great.
The enclosure has the capability to bolt the Essex circuit
board down using hinges. This gives you the ability to swing
the circuit board to the side and out of the way if you need
to run wires at a later time.
The pole can easily be routed with wires and is 36" longer
than the SPE100. This model is meant to be poured in concrete
so you can adjust the height of the console. This unit will
have that extra clean look with no mounting base plate or
bolts showing.
Dimensions: (The SPE200 is 83” tall and 23” deep.
From the faceplate to the front of the pole is 17”)
What’s included:
- (1)
SPE200
- (2) Hinged Standoffs
SAC
Not Included
|
 |
|
|
|
| Color & Texture |
|
|
